Integrated Circuits

Product Details:

Operational Amplifiers - Op Amps Quad Low Noise JFET


Low Power Consumption

Wide Common-Mode and Differential Voltage Ranges

Low Input Bias and Offset Currents
Output Short-Circuit Protection

Low Total Harmonic Distortion . . . 0.003% Typ

Product Details:

Operational Amplifiers - Op Amps Dual 25 uA 2.5V

Features • Low Input Offset Voltage: 250 µV (maximum) • Rail-to-Rail Output • Low Input Bias Current: 80 pA (maximum at +85°C) • Low Quiescent Current: 25 µA (maximum) • Power Supply Voltage: 2.5V to 6.0V • Unity-Gain Stable • Chip Select (CS) Capability: MCP608 • Industrial Temperature Range: -40°C to +85°C • No Phase Reversal • Available in Single, Dual and Quad Packages Typical Applications • Battery Power Instruments • High-Impedance Applications • Strain Gauges • Medical Instruments • Test Equipment Design Aids • SPICE Macro Models • FilterLab® Software • Mindi™ Circuit Designer & Simulator • Analog Demonstration and Evaluation Boards • Application Notes

Product Details:

NPN SILICON EPITAXIAL PLANAR TRANSISTORS IN TO92 PACKAGE

FEATURES: 1. This product is available in AEC-Q101 Compliant and PPAP Capable also.

Note: For AEC-Q101 compliant products, please use suffix -AQ in the part number while ordering.

APPLICATION: For switching and AF amplifier application

Product Details:

3-TERMINAL POSITIVE VOLTAGE REGULATOR

GENERAL DESCRIPTION:
The Voltages Available allow these Regulators to be used in Logic Systems, Instrumentation, Hi-Fi Audio Circuits and other Solid State Electronic Equipment

APPLICATION:
Industrial Power Supplies, SMPS Post Regulation, HVAC Systems ,AC Inventors ,Test and Measurement Equipment,Brushed and Brush less DC Motor Drivers,Solar Energy String Inverters

Additional Information:

• Item Code: LM7805M
• Delivery Time: IMMEDIATE
• Packaging Details: TUBE PACK

Product Details:

THREE-TERMINAL POSITIVE REGULATOR

GENERAL DESCRIPTIONS: The LM78LXX series of three-terminal positive regulators employ internal current limiting and thermal shutdown, making them essentially indestructible. If adequate heat-sink is provided, they can deliver up to 100 mA output current. They are intended as fixed voltage regulators in a wide range of applications including local or on-card regulation for elimination of noise and distribution problems associated with single-point regulation.In addition, they can be used with power pass elements to make high-current voltage regulators.The LM78LXX series used as Zener diode/resistor combination replacement, offers an effective output impedance improvement of typically two orders of magnitude, along with lower quiescent current and lower noise.

FEATURES: 1. Output current upto 100 mA
2. Output Voltage 3.3; 5; 6; 8; 9; 10; 12; 15; 18; 20; 24V
3. Thermal overload protection.
4. Short circuit protection.
5. No external components required.
6. This product is available in AEC-Q101 Compliant and PPAP Capable also. Note: For AEC-Q101 compliant products, please use suffix -AQ in the part number while ordering.

Additional Information:

• Item Code: LM78L05
• Delivery Time: IMMEDIATE
• Packaging Details: STRIP PACK

Product Details:

Features • Core: Arm® 32-bit Cortex®-M0+ CPU, frequency up to 64 MHz • -40°C to 85°C operating temperature • Memories – Up to 64 Kbytes of Flash memory with protection – 8 Kbytes of SRAM with HW parity check • CRC calculation unit • Reset and power management – Voltage range: 2.0 V to 3.6 V – Power-on/Power-down reset (POR/PDR) – Low-power modes: Sleep, Stop, Standby – VBAT supply for RTC and backup registers • Clock management – 4 to 48 MHz crystal oscillator – 32 kHz crystal oscillator with calibration – Internal 16 MHz RC with PLL option – Internal 32 kHz RC oscillator (±5 %) • Up to 44 fast I/Os – All mappable on external interrupt vectors – Multiple 5 V-tolerant I/Os • 5-channel DMA controller with flexible mapping • 12-bit, 0.4 µs ADC (up to 16 ext. channels) – Up to 16-bit with hardware oversampling – Conversion range: 0 to 3.6V • 8 timers: 16-bit for advanced motor control, four 16-bit general-purpose, two watchdogs, SysTick timer • Calendar RTC with alarm and periodic wakeup from Stop/Standby

Product Details:

Features  Core: ARM® 32-bit Cortex™-M0 CPU, frequency up to 48 MHz  Memories – 16 to 64 Kbytes of Flash memory – 4 to 8 Kbytes of SRAM with HW parity checking  CRC calculation unit  Reset and power management – Voltage range: 2.4 V to 3.6 V – Power-on/Power down reset (POR/PDR) – Low power modes: Sleep, Stop, Standby  Clock management – 4 to 32 MHz crystal oscillator – 32 kHz oscillator for RTC with calibration – Internal 8 MHz RC with x6 PLL option – Internal 40 kHz RC oscillator  Up to 55 fast I/Os – All mappable on external interrupt vectors – Up to 36 I/Os with 5 V tolerant capability  5-channel DMA controller  1 x 12-bit, 1.0 µs ADC (up to 16 channels) – Conversion range: 0 to 3.6 V – Separate analog supply from 2.4 up to 3.6 V  Up to 10 timers – One 16-bit 7-channel advanced-control timer for 6 channels PWM output, with deadtime generation and emergency stop – One 16-bit timer, with up to 4 IC/OC, usable for IR control decoding – One 16-bit timer, with 2 IC/OC, 1 OCN, deadtime generation and emergency stop – Two 16-bit timers, each with IC/OC and OCN, deadtime generation, emergency stop and modulator gate for IR contro

Product Details:

DUAL DIFFERNTIAL COMPARATORS


Single Supply or Dual Supplies
Wide Range of Supply Voltage− Max Rating . . . 2 V to 36 V− Tested to 30 V . . . Non-V Devices− Tested to 32 V . . . V-Suffix Devices
Low Supply-Current Drain Independent ofSupply Voltage . . . 0.4 mA Typ PerComparator
Low Input Bias Current . . . 25 nA Typ
Low Input Offset Current . . . 3 nA Typ(LM193)
Low Input Offset Voltage . . . 2 mV Typ
Common-Mode Input Voltage RangeIncludes Ground
Differential Input Voltage Range Equal toMaximum-Rated Supply Voltage . . . ±36 V
Low Output Saturation Voltage
Output Compatible With TTL, MOS, andCMOS

Product Details:

OCTAL BUFFERS AND LINE DRIVERSWITH 3-STATE OUTPUTS

Wide Operating Voltage Range of 2 V to 6 V􀀀 High-Current 3-State Outputs Drive BusLines Directly or Up To 15 LSTTL Loads􀀀 Low Power Consumption, 80-μA Max ICC􀀀 Typical tpd = 10 ns􀀀 ±6-mA Output Drive at 5 V􀀀 Low Input Current of 1 μA Max􀀀 Data Flow-Through Pinout (All Inputs onOpposite Side From Outputs)

Product Details:

FEATURES - 

* Fast switching capability* Avalanche energy tested* Improved dv/dt capability, high ruggedness

APPLICATIONS - 
High frequency switching mode power supply
Electronic ballast
LED power supplies

Product Details:

The ADS1230 is a precision 20-bit analog-to-digital converter (ADC). With an onboard low-noise programmable gain amplifier (PGA), onboard oscillator, and precision 20-bit delta-sigma ADC, the ADS1230 provides a complete front-end solution for bridge sensor applications including weigh scales, strain gauges, and pressure sensors.

The low-noise PGA has a gain of 64 or 128, supporting a full-scale differential input of ±39mV or ±19.5mV, respectively. The delta-sigma ADC has 20-bit effective resolution and is comprised of a 3rd-order modulator and 4th-order digital filter. Two data rates are supported: 10SPS (with both 50Hz and 60Hz rejection) and 80SPS. The ADS1230 can be clocked by the internal oscillator or an external clock source. Offset calibration is performed on-demand, and the ADS1230 can be put in a low-power standby mode or shut off completely in power-down mode.

All of the features of the ADS1230 are controlled by dedicated pins; there are no digital registers to program. Data are output over an easily-isolated serial interface that connects directly to the MSP430 and other microcontrollers.

The ADS1230 is available in a TSSOP-16 package and is specified from -40°C to +85°C.

Product Details:

RS-232 Interface IC 3-5.5V Multich RS- 232 Line Drvr/Rcvr

RS-232 Bus-Pin ESD Protection Exceeds±15 kV Using Human-Body Model (HBM)
Meets or Exceeds the Requirements ofTIA/EIA-232-F and ITU v.28 Standards
Operates With 3-V to 5.5-V VCC Supply
Operates Up To 250 kbit/s
Two Drivers and Two Receivers
Low Supply Current . . . 300 μA Typical
External Capacitors . . . 4 × 0.1 μF
Accepts 5-V Logic Input With 3.3-V Supply
Alternative High-Speed Pin-CompatibleDevice (1 Mbit/s)− SNx5C3232
Applications− Battery-Powered Systems, PDAs,Notebooks, Laptops, Palmtop PCs, andHand-Held Equipment

Additional Information:

• Delivery Time: IMMEDIATE
• Packaging Details: TAPE & REEL PACK

Product Details:

FEATURES
1. With Built - in Integrated Diode between Emitter & Collector
2. This product is available in AEC-Q101 Compliant and PPAP Capable also. Note: For AEC-Q101 compliant products, please use suffix -AQ in the part number while ordering.

APPLICATIONS: Suitable for Lighting, Switching Regulator and Motor Control

Product Details:

APPLICATIONS:

General Purpose Transistors Best Suited for use in Driver and Output Stages of Audio Amplifier

Product Details:

SOT-23 Plastic-Encapsulate Transistors

FEATURES 
Complementary to MMBT5551 
Ideal for Medium Power Amplification and Switching

Product Details:

2N3019 NPN SILICON PLANAR TRANSISTOR

FEATURE:
1. This product is available in AEC-Q101 Compliant and PPAP Capable also.
Note: For AEC-Q101 compliant products, please use suffix -AQ in the part number while ordering.

APPLICATIONS: General Transistor

Product Details:

Multiplexer Switch ICs HEF4052BT/SOT109/SO16

1. General descriptionThe HEF4052B is a dual single-pole quad-throw analog switch (2x SP4T) suitable for use inanalog or digital 4:1 multiplexer/demultiplexer applications. Each switch features four independentinputs/outputs (nY0, nY1, nY2 and nY3) and a common input/output (nZ). A digital enable input(E) and two digital select inputs (S1 and S2) are common to both switches. When E is HIGH,the switches are turned off. Inputs include clamp diodes. This enables the use of current limitingresistors to interface inputs to voltages in excess of VDD.2. Features and benefits• Wide supply voltage range from 3.0 V to 15.0 V• CMOS low power dissipation• High noise immunity• Fully static operation• 5 V, 10 V, and 15 V parametric ratings• Standardized symmetrical output characteristics• Complies with JEDEC standard JESD 13-B• ESD protection:• HBM JESD22-A114F exceeds 2000 V• MM JESD22-A115-B exceeds 200 V• Specified from -40 °C to +85 °C and -40 °C to +125 °C3. Applications• Analog multiplexing and demultiplexing• Digital multiplexing and demultiplexing• Signal gating

Additional Information:

• Item Code: HEF4052BT
• Delivery Time: IMMEDIATE
• Packaging Details: TAPE & REEL PACK

Product Details:

RS-485 Interface IC Low-Power RS-485 Transceiver

1 Features• Meets or exceeds the requirements of the TIA/EIA-485A standard• Low quiescent power– 0.3-mA Active mode– 1-nA Shutdown mode• 1/8 Unit load up to 256 nodes on a bus• Bus-pin ESD protection up to 15 kV• Industry-standard SN75176 footprint• Fail-safe receiver (bus open, bus shorted,bus idle)• Glitch-free power-up and power-down bus inputsand outputs2 Applications• Energy meter networks• Motor control• Power inverters• Industrial automation• Building automation networks• Battery-powered applications• Telecommunications equipment

Product Details:

MICROCHIP MICROCONTROLER

Extreme Low-Power Managementwith nanoWatt XLP:• Sleep mode: 20 nA, typical• Watchdog Timer: 300 nA, typical• Timer1 Oscillator: 800 nA @ 32 kHz• Peripheral Module DisableSpecial Microcontroller Features:• Full 5.5V Operation – PIC18FXXK22 devices• 1.8V to 3.6V Operation – PIC18LFXXK22 devices• Self-Programmable under Software Control• High/Low-Voltage Detection (HLVD) module:- Programmable 16-Level- Interrupt on High/Low-Voltage Detection• Programmable Brown-out Reset (BOR):- With software enable option- Configurable shutdown in Sleep• Extended Watchdog Timer (WDT):- Programmable period from 4 ms to 131s• In-Circuit Serial Programming™ (ICSP™):- Single-Supply 3V• In-Circuit Debug (ICD)

Additional Information:

• Delivery Time: IMMEDIATE
• Packaging Details: TRAY PACKED

Product Details:

ARM Microcontrollers - MCU Mainstream Arm Cortex-M0 Value line MCU 64 Kbytes of Flash , 48 MHz CPU

Features  Core: ARM® 32-bit Cortex™-M0 CPU, frequency up to 48 MHz  Memories – 16 to 64 Kbytes of Flash memory – 4 to 8 Kbytes of SRAM with HW parity checking  CRC calculation unit  Reset and power management – Voltage range: 2.4 V to 3.6 V – Power-on/Power down reset (POR/PDR) – Low power modes: Sleep, Stop, Standby  Clock management – 4 to 32 MHz crystal oscillator – 32 kHz oscillator for RTC with calibration – Internal 8 MHz RC with x6 PLL option – Internal 40 kHz RC oscillator  Up to 55 fast I/Os – All mappable on external interrupt vectors – Up to 36 I/Os with 5 V tolerant capability  5-channel DMA controller  1 x 12-bit, 1.0 µs ADC (up to 16 channels) – Conversion range: 0 to 3.6 V – Separate analog supply from 2.4 up to 3.6 V  Up to 10 timers – One 16-bit 7-channel advanced-control timer for 6 channels PWM output, with deadtime generation and emergency stop – One 16-bit timer, with up to 4 IC/OC, usable for IR control decoding – One 16-bit timer, with 2 IC/OC, 1 OCN, deadtime generation and emergency stop – Two 16-bit timers, each with IC/OC and OCN, deadtime generation, emergency stop and modulator gate for IR control – One 16-bit timer with 1 IC/OC 

Product Details:

ARM Microcontrollers - MCU 32BIT Cortex M3 64KB 20KB RAM 2X12 ADC

Features■ Core: ARM 32-bit Cortex™-M3 CPU– 72 MHz, 90 DMIPS with 1.25 DMIPS/MHz– Single-cycle multiplication and hardwaredivision– Nested interrupt controller with 43maskable interrupt channels– Interrupt processing (down to 6 CPUcycles) with tail chaining■ Memories– 32-to-128 Kbytes of Flash memory– 6-to-20 Kbytes of SRAM■ Clock, reset and supply management– 2.0 to 3.6 V application supply and I/Os– POR, PDR, and programmable voltagedetector (PVD)– 4-to-16 MHz quartz oscillator– Internal 8 MHz factory-trimmed RC– Internal 32 kHz RC– PLL for CPU clock– Dedicated 32

Product Details:

NPN HIGH VOLTAGE FAST-SWITCHING POWER TRANSISTOR

FEATURES: 1. This product is available in AEC-Q101 Compliant and PPAP Capable also.

Note: For AEC-Q101 compliant products, please use suffix -AQ in the part number while ordering.

APPLICATIONS: Energy-Saving Light, Electronics Ballasts, High Frequency Switching Power Supply, High Frequency Power Transform and Commonly Power Amplifier

Additional Information:

• Item Code: CD148
• Delivery Time: IMMEDIATE
• Packaging Details: AMMO PACK

Product Details:

P-CHANNEL MOSFET

MARKING : B84

DESCRIPTION: These are miniature surface mount MOSFETs, reduces power losses and conserve energy, making this device ideal for use in small power management circuitry

FEATURES:

1. Energy Efficient
2. Low Threshold Voltage
3. High-speed Switching
4. Miniature Surface Mount Package Saves Board Space

Product Details:

3AMP / 100V SURFACE MOUNT SCHOTTKY BARRIER RECTIFIER SMA PACKAGE

Features 

The plastic package carries Underwriters Laboratory Flammability Classification 94V-0 For surface mounted applications Metal silicon junction,majority carrier conduction Low power loss,high efficiency Built-in strain relief,ideal for automated placement High forward surge current capability High temperature soldering guaranteed: 250 °C/10 seconds at terminals

Product Details:

1 Features• High slew rate: 20 V/μs (TL07xH, typ)• Low offset voltage: 1 mV (TL07xH, typ)• Low offset voltage drift: 2 μV/°C• Low power consumption: 940 μA/ch (TL07xH, typ)• Wide common-mode and differentialvoltage ranges– Common-mode input voltage rangeincludes VCC+• Low input bias and offset currents• Low noise:Vn = 18 nV/√Hz (typ) at f = 1 kHz• Output short-circuit protection• Low total harmonic distortion: 0.003% (typ)• Wide supply voltage:±2.25 V to ±20 V, 4.5 V to 40 V2 Applications• Solar energy: string and central inverter• Motor drives: AC and servo drive control andpower stage modules• Single phase online UPS• Three phase UPS• Pro audio mixers• Battery test equipment

Product Details:

The STM32F030x4/x6/x8/xC microcontrollers incorporate the high-performance Arm^® Cortex^®-M0 32-bit RISC core operating at a 48 MHz frequency, high-speed embedded memories (up to 256 Kbytes of Flash memory and up to 32 Kbytes of SRAM), and an extensive range of enhanced peripherals and I/Os. All devices offer standard communication interfaces (up to two I²Cs, up to two SPIs and up to six USARTs), one 12-bit ADC, seven general-purpose 16-bit timers and an advanced-control PWM timer. The STM32F030x4/x6/x8/xC microcontrollers operate in the -40 to +85 °C temperature range from a 2.4 to 3.6V power supply. A comprehensive set of power-saving modes allows the design of low-power applications.
The STM32F030x4/x6/x8/xC microcontrollers include devices in four different packages ranging from 20 pins to 64 pins. Depending on the device chosen, different sets of peripherals are included. The description below provides an overview of the complete range of STM32F030x4/x6/x8/xC peripherals proposed.
These features make the STM32F030x4/x6/x8/xC microcontrollers suitable for a wide range of applications such as application control and user interfaces, handheld equipment, A/V receivers and digital TV, PC peripherals, gaming and GPS platforms, industrial applications, PLCs, inverters, printers, scanners, alarm systems, video intercoms, and HVACs.

Additional Information:

• Delivery Time: IMMEDIATE
• Packaging Details: TRAY PACKED

Product Details:

8 bit Microcontrollers MCU AVR 8KB 512B EE 16MHz 1KB SRAM

Features• High-performance, Low-power AVR® 8-bit Microcontroller• Advanced RISC Architecture– 130 Powerful Instructions – Most Single-clock Cycle Execution– 32 x 8 General Purpose Working Registers– Fully Static Operation– Up to 16 MIPS Throughput at 16 MHz– On-chip 2-cycle Multiplier• High Endurance Non-volatile Memory segments– 8K Bytes of In-System Self-programmable Flash program memory– 512 Bytes EEPROM– 1K Byte Internal SRAM– Write/Erase Cycles: 10,000 Flash/100,000 EEPROM– Data retention: 20 years at 85°C/100 years at 25°C(1)– Optional Boot Code Section with Independent Lock Bits• In-System Programming by On-chip Boot Program• True Read-While-Write Operation– Programming Lock for Software Security• Peripheral Features– Two 8-bit Timer/Counters with Separate Prescaler, one Compare Mode– One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and CaptureMode– Real Time Counter with Separate Oscillator– Three PWM Channels– 8-channel ADC in TQFP and QFN/MLF package• Eight Channels 10-bit Accuracy– 6-channel ADC in PDIP package• Six Channels 10-bit Accuracy– Byte-oriented Two-wire Serial Interface– Programmable Serial USART– Master/Slave SPI Serial Interface– Programmable Watchdog Timer with Separate On-chip Oscillator– On-chip Analog Comparator• Special Microcontroller Features– Power-on Reset and Programmable Brown-out Detection– Internal Calibrated RC Oscillator– External and Internal Interrupt Sources– Five Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, andStandby

Product Details:

Transistor Output Optocouplers Optocoupler Transistor DC Input

Features:• Current transfer ratio(CTR:MIN.50% at IF =5mA ,VCE =5V)• High isolation voltage between inputand output (Viso=5000 V rms )• Compact dual-in-line packageEL817*:1-channel type• Pb free• UL approved (No. E214129)• VDE approved (No. 132249)• SEMKO approved (No. 300858,300859,304855,304827,2022251,0143133/01-03,0101083/01,303345,303349)• NEMKO approved (No. P04203585, P00102385,P02101854)• DEMKO approved (No. 311822-01/02/03,310352-01,311822-03A)• CSA approved (No. 1143601)• BSI approved (No. 8592, 8593)• Options available:- Leads with 0.4”(10.16mm) spacing (M Type)- Leads bends for surface mounting (S and S1 Type)- Tape and Reel of TypeⅠ for SMD(Add”-TA” Suffix)- Tape and Reel of TypeⅡ for SMD(Add”-TB” Suffix)- The tape is 16mm and is wound on a 33cm reel• The product itself will remain within RoHS compliant version

Additional Information:

• Delivery Time: IMMEDIATE
• Packaging Details: TAPE IN REEL

Product Details:

SURFACE MOUNT SCHOTTKY BARRIER RECTIFIER

 The plastic package carries Underwriters Laboratory Flammability Classification 94V-0
 For surface mounted applications
 Metal silicon junction,majority carrier conduction
 Low power loss,high efficiency
 Built-in strain relief,ideal for automated placement
 High forward surge current capability
 High temperature soldering guaranteed: 250 °C/10 seconds at terminals

Product Details:

SURFACE MOUNT SCHOTTKY BARRIER RECTIFIER


Features
The plastic package carries Underwriters Laboratory Flammability Classification 94V-0
For surface mounted applications
Metal silicon junction,majority carrier conduction
Low power loss,high efficiency
Built-in strain relief,ideal for automated placement
High forward surge current capability
High temperature soldering guaranteed: 250 °C/10 seconds at terminals

Product Details:

Transistor Output Optocouplers

Additional Information:

• Item Code: A
• Production Capacity: A
• Delivery Time: IMMEDIATE
• Packaging Details: TAPE & REEL

Product Details:

CHIP TANTALUM

RANGE - 0.1UF TO 470UF

CASE - A / B / C / D / E

Product Details:

N CHANNEL ENHANCEMENT MODE FIELD EFFECT TRANSISTOR

FEATURES:
1. High density cell design for low RDS(ON)
2. Voltage controlled small signal switch
3. Rugged and reliable
4. High saturation current capability
5. ESD protected up to 2KV APPLICATION: Designed for High Speed Pulse Amplifier and Drive Application

Additional Information:

• Item Code: 2N7002K
• Delivery Time: IMMEDIATE
• Packaging Details: TAPE & REEL PACK

Product Details:

MICROCONTROLER

FeaturesHigh Performance, Low-Power AVR® 8-bit Microcontroller Family• Advanced RISC Architecture– 131 Powerful Instructions– Most Single Clock Cycle Execution– 32 x 8 General Purpose Working Registers– Fully Static Operation– Up to 20 MIPS Throughput at 20 MHz– On-Chip 2-Cycle Multiplier• High Endurance Nonvolatile Memory Segments– 32 KB of In-System Self-Programmable Flash program memory– 1 KB EEPROM– 2 KB Internal SRAM– Write/Erase Cycles: 10,000 Flash/100,000 EEPROM– Optional Boot Code Section with Independent Lock Bits• In-System Programming by On-chip Boot Program• True Read-While-Write Operation– Programming Lock for Software Security

Additional Information:

• Delivery Time: IMMEDIATE
• Packaging Details: TRAY PACK

Product Details:

MICRO CONTROLLERS